9 Best Backup Cameras for Trucks and Trailers (November 2026)
The best backup cameras for trucks and trailers include the Pemacom 1080P Magnetic Wireless Backup Camera (best overall), the LeeKooLuu 7-Inch Wireless Truck Backup Camera for quick wireless install, and the Yakry 7-Inch Plug and Play Wired RV Backup Camera for constant towing.
On this page (10 sections)
- The best backup cameras for trucks and trailers
- How these backup cameras compare
- How we picked these truck and trailer cameras
- Which mount suits your trailer: magnet, plate or bracket?
- How far does a wireless signal need to reach?
- How do you wire a camera that stays on the trailer?
- Do you need one camera or two?
- Battery, solar or vehicle power: which is simpler?
- Screen, phone or both: what do you look at?
- Verdict: the right camera depends on how often you hitch up
The best backup camera for truck and trailer setups is the Pemacom 1080P Magnetic Wireless, which sticks to the trailer in about a minute and sends a clear picture to a 7-inch screen in the cab. Pick the LeeKooLuu 7-Inch if you want a wireless link without pairing, the Yakry 7-Inch Wired if you tow one trailer all season, or the Casoda if you would rather use your phone than fit a monitor.
Truck and trailer buyers split into two camps, and your kit should follow your habit. People who hitch up the same trailer every weekend are happiest with a cable, because it never drops the picture.
People who swap trailers, haul for work or rent a rig now and then want a camera that lifts off and reapplies in seconds. That is where the magnetic kits win.
Our picks at a glance
-
1
-
2
Best for quick wireless installLeeKooLuu 7-Inch Wireless Truck Backup Camera
8.7/10 our score
See it on Amazon -
3
Best for constant towingYakry 7-Inch Plug and Play Wired RV Backup Camera
8.3/10 our score
See it on Amazon
- 4
Check itPemacom Dual Wireless Backup Camera, 15200mAh Battery
Best for long off-grid trips - 5
Check itYakry Dual 7-Inch Split Screen Truck Backup Camera
Best for front and rear coverage - 6
Check itVTimes Wireless Backup Camera for Trucks
Best for long rigs - 7
Check itThybro 1080P Strong Magnetic Wireless Trailer Camera
Best for moving between trailers - 8
Check itCasoda Magnetic Rechargeable WiFi Backup Camera
Best for phone-only setups - 9
Check iteRapta Dual Magnetic Solar Wireless Backup Cameras, 7-Inch
Best for campsite security
The best backup cameras for trucks and trailers
The top pick balances easy mounting with a battery that survives a long trip; every other camera here wins on one specific need. Read each entry for the job it handles best.
Pemacom 1080P Magnetic Wireless Backup Camera: Best overall
- Magnetic mount, no wiring
- 15,000mAh battery plus 5W solar panel
- 7-inch HD screen
- IP69 waterproof
The strongest all-round pickup: a magnet-on camera for the trailer, a big screen for the cab, and solar charging so the battery keeps up on long trips.
Pros
- Moves between trailers in a minute
- 15000mAh battery with solar top-up
- Dual video channels for a second camera
Cons
- Needs a metal surface or an added plate
- Signal range of 33 ft limits very long rigs
Pemacom suits most drivers because it removes the two hardest parts of a trailer install: running wire and charging a camera. Six magnets in a rubber-coated base grip a metal surface, so you can add a rear view in about a minute.
Inside is a 15,000mAh battery and a 5W solar panel. Five hours on USB-C gives up to 24 hours of use, and the panel keeps it topped up on sunny days.
The 7-inch screen shows a 1080P picture from a 170 degree lens, with parking lines and dual video channels for a second camera. The 2.4GHz link reaches about 33 ft and uses frequency hopping to hold its picture without frame drops or delays.
When the monitor is switched off at the cigarette lighter, the camera drops into a sleep mode so the battery is not drained between trips. The housing is ABS plus PC and the camera is rated IP69, so rain and washdowns are not a problem.
Buy it for the easiest all-round setup on a pickup and trailer you also drive without the trailer. Longer rigs should look at the VTimes for signal reach.
LeeKooLuu 7-Inch Wireless Truck Backup Camera: Best for quick wireless install
- Pre-paired Bluetooth wireless link
- 7-inch monitor with suction cup mount
- IP69 waterproof
- Supports two cameras
A no-pairing wireless kit that powers the camera from a reverse or running light and puts a large screen on the windshield.
Pros
- Pre-paired out of the box
- Adjustable parking lines
- Split screen for two cameras
Cons
- Camera still needs a power wire
- 150 degree lens covers less width
LeeKooLuu suits the driver who wants a wireless camera but does not mind one small wire. The camera connects to a reverse light, running light or other power source, and the monitor and camera then link over Bluetooth without any pairing step.
Setup takes about 15 minutes. The 7-inch screen shows 1080P video with automatic night vision, a 150 degree view and adjustable parking lines you can set to your trailer.
Add a second camera and the split screen shows both feeds, switching channels with one press of the CH button. The whole kit is IP69 rated for rain, snow and washdowns.
The monitor sits on an adjustable suction cup mount, so you can angle it toward the driver's seat.
Because the camera draws from the truck's lights, there is no battery to charge or solar panel to keep clear. The trade is that one wire, and a 150 degree lens that covers a little less width than the 170 degree Pemacom.
Choose it over the Pemacom if you prefer a camera wired to the vehicle's power instead of a battery. Choose the Pemacom if even one wire is too much.
Yakry 7-Inch Plug and Play Wired RV Backup Camera: Best for constant towing
- 66 ft cable to the monitor
- 7-inch IPS screen with sunshade
- IR night vision
- Two video inputs
The wired choice for a truck and trailer that stay hitched, because a cable does not lose signal the way a wireless link can.
Pros
- Stable signal with no lag
- One power supply feeds camera and monitor
- Sunshade keeps the screen readable
Cons
- Rigging 66 ft of cable takes real time
- Not practical to move between trailers
Yakry's wired kit suits the owner who tows the same trailer week after week and wants a picture that never stutters. A 66 ft cable runs from the camera to the monitor, and a single power supply feeds both, so there is no second feed to wire.
The 7-inch IPS screen comes with an anti-glare sunshade and keeps colors steady from an angle. IR night vision and a 150 degree non-fisheye lens help in dim driveways.
Image flip turns the view into a mirror image for reversing, and a second camera can be added to the V2 input. Yakry backs it with three years of replacement service.
The cable itself has a dual-layer shielding structure and copper interfaces to resist bending and wear.
Pick this one for a permanent install on a work truck or travel trailer. Skip it if you need to switch the camera between trailers.
Pemacom Dual Wireless Backup Camera, 15200mAh Battery: Best for long off-grid trips
- Two solar magnetic cameras
- 15200mAh battery, up to 26 hours
- 450 ft wireless range
- 7.2-inch split screen
A two-camera kit for rigs that spend days away from shore power, with a bigger battery and longer signal reach than most picks here.
Pros
- Two cameras cover rear and side views
- 26 hours of use per charge
- Long 450 ft signal range
Cons
- Higher cost than single-camera kits
- Bulky monitor setup for a small cab
Pemacom's dual kit suits the camper or long-haul driver who spends days away from a power outlet. Two solar magnetic cameras ride on the trailer, and the 15200mAh battery gives up to 26 hours of run time, enough for a weekend of reversing and driving.
The 7.2-inch split screen shows both feeds and covers more area than a small 5-inch display. The 2.4GHz signal reaches up to 450 ft in open air and holds steady at highway speed.
Cameras are IP69K rated and record in a loop while parked, which helps on overnight stays. Night vision reaches about 30 ft.
Each camera uses a 1080P sensor with an F1.6 glass lens and a 170 degree view, and the monitor runs off USB with a suction cup mount.
Mounting is a one-second magnetic job on each camera, so you can move them from the rear to the side or down to the hitch as needed. The kit also ships with iron brackets for surfaces that are not steel.
Choose it when rear and side views both matter on a long trailer. For a simple single-camera job, the top pick costs less and mounts faster.
Yakry Dual 7-Inch Split Screen Truck Backup Camera: Best for front and rear coverage
- Two cameras with split screen
- 33 ft and 66 ft cables
- 7-inch 1080P screen with sunshade
- IR night vision to 50 ft
The wired dual-camera kit to pick when you want both a front and a rear view at once on one screen.
Pros
- Two long cables suit long trailers
- Split screen shows both feeds
- Metal, IP69 waterproof housing
Cons
- Both cameras need cable runs
- Longer setup than a magnetic kit
Yakry's dual wired kit suits the driver who wants a front view and a rear view on one screen at the same time. It ships with two cameras, a 7-inch 1080P screen and cables of 33 ft and 66 ft so you can cover a long trailer.
The split screen shows both feeds at once. IR night vision reaches 50 ft, and a metal IP69 housing handles rain, mud and pressure washing.
The system works on 12V to 24V, which covers most trucks and tractors.
Parking lines and image flip make backing easier, and the 150 degree lens takes in the full width behind you. The wired RCA link means no signal loss while reversing or changing lanes.
A sunshade keeps glare off the screen in strong light.
Pick it for a fixed rig where you want eyes front and back. Skip it if setup time matters more than coverage.
VTimes Wireless Backup Camera for Trucks: Best for long rigs
- Up to 984 ft signal in open areas
- Blind spot detection with alert
- 7-inch screen, four channels
- IP69K waterproof
The pick when cab and trailer sit far apart, thanks to the longest signal range here and a blind spot warning that highlights close objects.
Pros
- Long signal range for big trailers
- Blind spot alerts you can toggle
- Records to a micro SD card
Cons
- Lower resolution than most picks here
- Needs a micro SD card for recording
VTimes suits the driver with a long cab-to-trailer gap. Its 2.4GHz link reaches up to 984 ft in open areas, well beyond the rest of this group, so a big rig keeps a clear picture.
The signal uses FM encryption and picks the best free channel to avoid interference.
The 7-inch screen runs four channels online at once, and blind spot detection highlights an object or person near the trailer and sounds an alert. You can switch that alert off if it is too chatty.
The camera is IP69K rated and all metal, with 20 IR lights for night work and adjustable parking lines. Recording to a micro SD card of 8GB to 128GB is supported, though the card is not included.
The kit includes a mounting bracket for pre-wired Furrion systems, so an RV with that setup can plug straight in.
The view angle is 120 degrees and the stated resolution is lower than most picks here, so the long reach is the reason to choose it rather than image sharpness.
Choose it for signal range first. Choose another pick if you want a sharper 1080P image.
Thybro 1080P Strong Magnetic Wireless Trailer Camera: Best for moving between trailers
- Magnetic base with 50 lb pull
- 15000mAh battery plus solar
- 5.8GHz wireless up to 56 ft
- 170 degree lens
A strong magnet and a long battery life make this the easy one to shift from trailer to trailer.
Pros
- Magnet rated at 50 lb of pull
- More than 17 hours per charge
- 170 degree lens covers wide
Cons
- Shorter wireless reach than the other magnetic picks
- Screen mount needs thought on rough roads
Thybro suits the owner with several trailers and one kit to share. The NdFeB magnetic base is rated at 50 lb of pull, five times the camera's weight, so it holds on rough roads and at highway speed.
A rubber base protects the paint when you lift it off.
A 15000mAh battery runs more than 17 hours, and a solar panel plus USB-C charging keeps it ready between trips. The 5.8GHz link stays stable up to 56 ft, enough for a 40 ft trailer.
Dual antennas help hold the signal at speed.
The 170 degree lens shows obstacles bumper to bumper, and the 7-inch monitor is pre-paired for plug and play. IP69K seals out rain, snow and mud, and infrared LEDs keep the picture usable after dark.
The kit includes a charge plug and cables for the camera and monitor.
Pick it for easy swapping between trailers. Its wireless reach is shorter than the VTimes, so very long rigs should look elsewhere.
Casoda Magnetic Rechargeable WiFi Backup Camera: Best for phone-only setups
- No screen, uses your phone
- 5G WiFi up to 45 ft
- 9600mAh rechargeable battery
- 180 degree angle adjustment
The budget-friendly way to add a camera without a monitor: it streams to your phone over WiFi and runs fully on battery.
Pros
- No monitor to mount
- Rotates 180 degrees without tools
- Cheaper than screen kits
Cons
- Phone must be free to act as screen
- Signal reach of about 45 ft
Casoda suits the driver who would rather not fit a second screen. The camera streams over 5.8GHz WiFi to your phone or tablet, so the dashboard stays clear and the cost stays low.
Its 9600mAh battery and magnet mean no wires at all; you set the angle by rotating the camera 180 degrees, no screws needed. The 1080P CCD sensor and 12 IR lights keep the picture usable at night.
H.265 encoding keeps the stream smooth at a high frame rate.
The signal covers about 45 ft, so it fits a standard pickup and trailer. The camera sleeps after 30 minutes idle, and it needs 8 to 10 hours of charging before first use.
A dedicated app handles WiFi connection, battery level and the reversing guidelines, and the maker offers software-level support.
Choose it for a phone-based setup on a budget. Choose a screen kit if you want the view on the dash all the time.
eRapta Dual Magnetic Solar Wireless Backup Cameras, 7-Inch: Best for campsite security
- Touchscreen monitor
- Blind spot detection with alerts
- 32GB SD card for loop recording
- Two solar magnetic cameras
A two-camera kit with touchscreen controls and built-in recording that doubles as a parked security set at the campsite.
Pros
- Touchscreen controls parking lines
- Records continuously to an SD card
- Two cameras with solar charging
Cons
- Shorter in-vehicle range than the long-range kits
- Battery life depends on good sunlight
eRapta suits the camper who wants a camera at the hitch and a watchful eye once parked. Two solar magnetic cameras feed a 7-inch touchscreen where you set parking lines, record and play back with a tap.
The 32GB SD card records in a loop, overwriting old footage, so the kit doubles as a security set at the campsite. Blind spot detection adds audio and visual alerts while reversing.
The touchscreen makes setup quicker than button-only menus.
Eight IR lights handle low light, and the cameras are IP69K rated. Up to four cameras can connect, and the 2.4GHz signal reaches about 40 ft in a vehicle.
Battery indicators sit on both the camera and the monitor, and the cameras sleep when the monitor shuts down to save charge.
Choose it for recording and touch controls. Its in-vehicle range is shorter than the long-range kits, so it fits short trailers best.
How these backup cameras compare
The fastest setups are the magnetic wireless kits, while the wired ones give the steadiest picture for a permanent install. Use this table to narrow the field before you read the product sections.
| Product | Best for | Screen | Mount | Connection | Our score |
|---|---|---|---|---|---|
| Pemacom 1080P Magnetic Wireless Backup Camera | overall | 7 in LCD | Magnet camera, suction cup monitor | 2.4GHz wireless | 9.2 |
| LeeKooLuu 7-Inch Wireless Truck Backup Camera | quick wireless install | 7 in LCD | Suction cup, surface mount | Bluetooth wireless | 8.7 |
| Yakry 7-Inch Plug and Play Wired RV Backup Camera | constant towing | 7 in IPS | Dashboard or surface mount | Wired, 66 ft cable | 8.3 |
| Pemacom Dual Wireless Backup Camera, 15200mAh Battery | long off-grid trips | 7.2 in split screen | Magnetic cameras, suction cup monitor | 2.4GHz wireless | 8.2 |
| Yakry Dual 7-Inch Split Screen Truck Backup Camera | front and rear coverage | 7 in LCD | Bracket mount | Wired, RCA | 8.1 |
| VTimes Wireless Backup Camera for Trucks | long rigs | 7 in LCD | Suction cup or dashboard | 2.4GHz wireless | 8.0 |
| Thybro 1080P Strong Magnetic Wireless Trailer Camera | moving between trailers | 7 in DVR monitor | Magnetic, surface mount | 5.8GHz wireless | 7.4 |
| Casoda Magnetic Rechargeable WiFi Backup Camera | phone-only setups | Phone or tablet | Magnetic, surface mount | 5.8GHz WiFi | 7.2 |
| eRapta Dual Magnetic Solar Wireless Backup Cameras, 7-Inch | campsite security | 7 in touchscreen | Magnetic, surface mount | 2.4GHz wireless | 7.0 |
How we picked these truck and trailer cameras
We compared specs against the two ways people buy: a camera that swaps between trailers and a camera that stays bolted to one rig. Magnetic bases, battery capacity and signal range decide the first group, while cable length, screen quality and lag decide the second.
We weighed mounting hardware, screen size, waterproof rating and night vision, then favored kits that solve a clear job. Our score weighs specs, features and buyer feedback against what you're shopping for.
Which mount suits your trailer: magnet, plate or bracket?
A magnetic mount is the right choice for most people who move a camera between trailers, while a bracket or plate mount fits a camera that stays put. The mount matters more than the camera, because a loose camera ruins even a good picture.
Magnet mounts
A magnet camera with a rubber base sticks to a steel panel and lifts off in seconds. The Pemacom, Thybro and Casoda kits here use this style.
The Pemacom base uses six rare earth magnets and the Thybro base is rated at 50 lb of pull.
Clean the surface first so grit does not scratch the paint. Aluminum or plastic panels need a steel plate behind the camera, and most kits include one.
The Casoda kit also needs a metal plate for aluminum carriages.
Plate and bracket mounts
A bracket mount bolts on and never shifts, so it suits a trailer you keep. The Yakry Dual uses a bracket, and the LeeKooLuu mounts at a standard license plate spot.
The Yakry Plug and Play camera is a surface mount.
These take longer to fit but need no thought after that. If you plan to keep the camera on the same trailer, a fixed mount is the sturdier pick.
The trade-off is that moving it to another rig means undoing the screws and resealing the holes.
How far does a wireless signal need to reach?
Measure from the camera on the trailer to the monitor in the cab, then add a margin, because steel and glass cut the range. Short trailers usually sit well inside the reach of any kit here, while long fifth wheels and gooseneck rigs need the longer links.
Here is what each pick claims:
- Pemacom Magnetic: about 33 ft
- Pemacom Dual: up to 450 ft in open areas
- VTimes: up to 984 ft in open areas
- Thybro: up to 56 ft
- Casoda: about 45 ft
- eRapta: up to 40 ft in a vehicle, 320 ft in open areas
A 30 ft travel trailer fits most of these. A 40 ft fifth wheel is safer with the VTimes or Pemacom Dual.
For a wireless kit built around towing, see our guide to the wireless backup camera for trailer setups that hold a signal on the move.
How do you wire a camera that stays on the trailer?
If you pick a wired kit, plan the cable run before you drill anything. Run the cable along the trailer frame, keep it away from sharp edges and hot exhaust parts, and leave a little slack at the hitch so turning does not stretch it.
The Yakry Plug and Play needs one power source for both camera and monitor, which keeps the wiring simple. The Yakry Dual comes with 33 ft and 66 ft cables for a long trailer, so measure your rig before you pick which one to run.
If you are fitting a travel trailer for the first time, our walkthrough on how to add backup camera to travel trailer covers routing and power taps step by step. On a wireless kit the camera still needs a charge or a light tap, so plan where the cable or panel will sit either way.
Do you need one camera or two?
Two cameras make sense when you reverse a long trailer, tow at night or want a view of the hitch and the rear at once. One camera covers a standard pickup and trailer for most drivers.
A second camera pays off in three common cases:
- Watching the hitch ball while lining up, then switching to the rear view.
- Seeing down both sides of a wide trailer in tight campsites.
- Keeping an eye on a boat, horse or cargo load behind the cab.
The Pemacom Dual, Yakry Dual and eRapta kits here ship with two cameras. The top pick, LeeKooLuu and VTimes systems accept a second camera later.
Camper owners often want that extra view, and our pick of the backup camera for camper trailers covers the layouts that suit them.
Battery, solar or vehicle power: which is simpler?
Battery and solar kits are the simplest to fit because nothing taps the truck's wiring; vehicle-powered kits never need charging but take a wire. Match the choice to how often you tow and how easy it is to reach a charger.
A solar panel helps if the trailer sits outside between trips. The Pemacom Magnetic gets up to 24 hours from a 5-hour charge, the Pemacom Dual runs up to 26 hours, and the Thybro lasts more than 17 hours.
The eRapta cameras also charge from the sun, and the Casoda camera runs on a 9600mAh battery charged by USB.
Vehicle power suits a camera that is always on the same rig. The LeeKooLuu camera taps a light circuit, while the Yakry wired kits share one supply with the monitor.
Work truck fleets often prefer that, and our roundup of the backup camera for box truck options shows how the wiring plays out on a bigger body.
Screen, phone or both: what do you look at?
A dedicated 7-inch screen gives the clearest view at a glance and stays on the dash all the time, which is what most drivers want. A phone-based camera like the Casoda saves the cost and dash space but ties up your phone while reversing.
Touch screens, like the eRapta, add tap controls for parking lines and playback. Split screens, like the Pemacom Dual and Yakry Dual, show two feeds at once.
The Pemacom Magnetic and LeeKooLuu both offer split-screen support so you can add a second feed later.
If you only reverse a few times a day, a basic screen is enough. For daily towing in tight lots, the larger screen and parking lines earn their keep.
Verdict: the right camera depends on how often you hitch up
The Pemacom 1080P Magnetic Wireless is the best backup camera for truck and trailer duty for most drivers, because it mounts in a minute, charges from the sun and shows a clear 1080P picture on a 7-inch screen. It suits the owner who swaps trailers and wants one kit to do it all.
Go wired with the Yakry Plug and Play if you tow one trailer all season and want a picture that never drops. Pick the LeeKooLuu for a wireless link that feeds off the truck's power, the Pemacom Dual or Yakry Dual for two views, and the VTimes when the cab and trailer sit far apart.
Then clean the mounting spot, check the surface is steel, and take one slow pass with the camera running before your first real tow.
Our top 3 picks at a glance
-
1
-
2
Best for quick wireless installLeeKooLuu 7-Inch Wireless Truck Backup Camera
8.7/10 our score
See it on Amazon -
3
Best for constant towingYakry 7-Inch Plug and Play Wired RV Backup Camera
8.3/10 our score
See it on Amazon
Frequently asked questions
Do I need a wired or a wireless backup camera for a trailer?
A wired camera gives the most stable picture on a rig that stays hitched, while a wireless camera is easier to move between trailers. Pick wired if you tow one trailer every week and magnetic wireless if you swap often.
How long does a wireless trailer camera battery last?
Battery figures here range from a 15,000mAh pack good for about 24 hours to a 15200mAh kit rated for up to 26 hours of continuous use. A solar panel tops up the battery between trips and stretches the gap between charges.
Can a backup camera see the hitch ball while I line up?
Yes, if you aim the camera at the hitch area before you back up. A magnetic camera with a wide 170 degree lens is the easiest to reposition for hitch alignment, then turn back to the road once you are connected.
How far can a wireless backup camera transmit?
Reach varies a lot: about 33 ft on the Pemacom magnetic kit, up to 56 ft on the Thybro, and up to 984 ft in open air on the VTimes. Steel trailer bodies cut that down, so keep the camera antenna in line with the cab.
Will a magnet camera stay on at highway speed?
A strong magnet with a rubber base holds well on smooth metal, and the Thybro base is rated at 50 lb of pull. Clean the surface first and add a metal plate if your trailer panel is aluminum or plastic.
About this guide: Our look at backup cameras for trucks and trailers draws on maker specs, materials and what owners report. See how we research.



